Genuine Oem Engine Oil Filter Housing Cover O Ring For Vw Audi 06E115446
Introduction Condition: New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is ... Read moreabout the condition Part Type: Engine Oil Filter Housing Cover
Send Inquiry
Introduction
-
Condition:
-
-
Part Type:
-
Engine Oil Filter Housing Cover O-Ring
-
Manufacturer Part Number:
-
06E115446
-
Brand:
-
YJM
Product Overview and Identification
This engine oil filter housing cover O-ring is identified for VW/Audi applications and carries manufacturer part number 06E115446. It is a sealing component associated with the oil filter housing cover, rather than the cover or the oil filter itself. Its purpose is to fit at the cover-to-housing sealing point when the matching application calls for this part number. Correct identification matters because an O-ring must correspond to the design of the housing and cover to sit properly and perform its intended sealing role.
The product title describes the item as genuine OEM, while the listing details show YJM in the brand field and 06E115446 as the manufacturer part number. Use the part number as a key reference when comparing this item with the part being replaced or with vehicle service information. This listing does not specify a vehicle year, model, engine, dimensions, or material, so confirm those details through the applicable parts catalog or a qualified parts professional before ordering. Checking first can help avoid selecting a similar-looking seal that is not intended for the same housing.
Sealing Role and Practical Benefits
An O-ring provides a compact, continuous seal where compatible components meet. In this application, the ring is intended for the engine oil filter housing cover. When the correct part is seated as designed and the cover is installed correctly, the seal helps contain engine oil at this joint during normal operation. Replacing a seal that is damaged, displaced, or no longer suitable during related service can support a clean assembly and reduce the risk of leakage at the cover area. The O-ring works as part of the complete housing and cover assembly; it does not replace the need to inspect those components or follow the vehicle maker’s service procedure.
For maintenance teams, repair shops, and vehicle owners coordinating an oil filter service, identifying the seal separately makes it easier to plan for the small service components that may be required during reassembly. A suitable replacement can help restore the intended sealing interface after the cover has been removed. It can also be useful to have the correct part available before beginning work, helping limit interruptions once the oil filter housing is open. These practical benefits depend on verifying fitment and using the part in the application for which it is specified; no performance result can be assumed if the part number or installation is incorrect.
Replacement and Installation Considerations
Before installation, compare the replacement with the removed O-ring and confirm the part number against the vehicle’s service information. Check that the seal is intact and that the housing cover and its sealing groove are clean and free of visible damage or debris. Position the O-ring in its intended groove without twisting, stretching, or pinching it. Avoid forcing a seal that does not sit naturally in the matching location; resistance or a mismatch may indicate that the application or part selection should be checked again. Follow the vehicle manufacturer’s instructions for removing and reinstalling the oil filter housing cover, including any specified service steps.
After reassembly, inspect the cover area for signs of oil seepage in accordance with the appropriate service procedure. If leakage continues, review the installation and inspect related mating surfaces rather than assuming that replacing the O-ring alone resolves every possible cause. This product listing does not provide installation torque, tools, dimensions, or a vehicle-specific procedure, so consult the correct repair information for those requirements. Careful preparation, correct part identification, and clean handling help protect the sealing surfaces and support dependable maintenance work.
Ordering and Application Checks
When ordering, use 06E115446 as the primary reference shown for this engine oil filter housing cover O-ring. Check the number against the existing part, a reliable vehicle parts lookup, or the information supplied by a VW/Audi parts specialist. The title indicates a VW/Audi application, but the available product details do not list exact vehicle compatibility. Do not rely on vehicle make alone if multiple engine or housing configurations may apply. Confirming the specific application before purchase helps ensure that the ring corresponds to the intended cover and housing.
The condition is listed as new: a brand-new, unused, unopened, and undamaged item in its original packaging, with the condition description continuing in the listing. The part type is Engine Oil Filter Housing Cover O-Ring, the manufacturer part number is 06E115446, and the brand field is YJM. Review these details together when selecting the replacement, and contact the seller or a qualified parts professional if any listing information needs clarification. This careful check is useful for individual maintenance purchases as well as workshop parts sourcing, where matching the reference number helps keep service planning accurate.
Send an Inquiry
Related Products
Yjm Oil Sump Gasket 11 13 7 600 482
Fitment The YJM oil sump gasket, reference 11 13 7 600 482, is listed for both left-hand-drive and right-hand-drive models. This fitment information is intended···
Yjm Oil Sump Gasket 11 13 7 511 224
Fitment This YJM oil sump gasket is listed for the BMW vehicle applications below. Use the fitment information as a starting point when identifying a replacemen···
Seal Oil Filter Housing Engine Side Bmw Petrol 11427537293
This product is identified as a seal for the engine-side oil filter housing on BMW petrol vehicles. The product reference is 11427537293. When servicing the oil···
Oil Sump Gasket 11137548031 Bmw
BMW Oil Sump Gasket 11137548031 The oil sump gasket identified by part number 11137548031 is a BMW replacement part intended for use at the joint between the en···