Oil Drain Plug Gaskets Crush Washers Seals Rings Vw N 013 815 7
This oil drain plug gasket, also described as a crush washer, seal, or ring, is intended for use at the drain plug connection during vehicle maintenance. The product reference is VW N 013 815 7. Its
Send InquiryOil Drain Plug Gasket and Crush Washer Overview
This oil drain plug gasket, also described as a crush washer, seal, or ring, is intended for use at the drain plug connection during vehicle maintenance. The product reference is VW N 013 815 7. Its role in an oil service is to sit at the mating point between the drain plug and the oil pan, helping create a sealing interface when the plug is reinstalled. A suitable gasket supports a careful, tidy service procedure and helps reduce the chance of oil escaping from the drain-plug area after maintenance.
A drain plug washer is a small service component, but it matters whenever the plug is removed to drain engine oil. Replacing or checking the washer as part of the service helps keep attention on the complete connection rather than on the bolt alone. Correct fit is essential: compare the part reference and the vehicle application before installation, and confirm that the selected gasket matches the drain plug and service requirements for the vehicle.
Suitable cars
Listed Vehicle Makes and Application Checks
The vehicle makes listed for this oil drain plug gasket are AUDI, AUVERLAND, BENTLEY, CHEVROLET, CITROËN, CUPRA, FIAT, FORD, FSO, HYUNDAI, LADA, LANCIA, LDV, MEGA, NISSAN, PEUGEOT, PORSCHE, ROVER, SANTANA, SEAT, SKODA, SUZUKI, TOYOTA, UAZ, and VOLKSWAGEN. This broad make list is provided as an application reference; it does not replace checking the specific vehicle, engine, drain plug, or required part number.
Before ordering, compare the gasket reference with the number used for the vehicle being serviced. Vehicle make alone may not identify the correct replacement, so use the OE-number information below alongside the vehicle’s service information or parts records. This extra check is useful for workshops managing different makes as well as for parts buyers sourcing a washer for a planned oil change.
During service, check that the drain plug and its contact area are clean and in suitable condition before fitting the replacement. Seat the washer correctly and follow the vehicle manufacturer’s service procedure for reinstalling the plug. These routine checks support consistent maintenance practice without relying on assumptions about a vehicle’s configuration or on a part number that has not been verified.
OEM Number Cross-Reference
Use the OE references below to compare this oil plug washer with the number specified for the vehicle or replacement part. The listed references span several manufacturers. Check punctuation and spacing carefully when comparing a reference, and confirm fitment for the intended vehicle before placing an order or beginning a repair.
OEM-NUMBER
Proceed to comparison by OEM number
- AUDI / CUPRA / SEAT / SKODA / VW - OE-N 013 815.6
- AUDI / SEAT / SKODA / VW - OE-N 013 815 7
- BMW - OE-07 11 9 963 244
- CITROËN / DS / PEUGEOT - OE-0313.27
- DAF - OE-0324 658
- DEUTZ / KHD / MAGIRUS-DEUTZ - OE-0114 3588
- FIAT - OE-9400313279
- HYUNDAI / KIA - OE-21513-29000
- MERCEDES-BENZ - OE-915035 000017
- MERCEDES-BENZ - OE-N 915035 000017
- RENAULT TRUCKS - OE-00 24 463 104
- TOYOTA - OE-SU001-00188
The cross-reference is provided to make parts comparison clearer, including when the vehicle make differs from the VW reference in the product title. Treat these numbers as comparison points rather than as a substitute for checking the exact application. If the existing washer or drain plug carries a different reference, verify the correct replacement through the vehicle’s parts information before proceeding.
Oil Service and Replacement Considerations
Including the drain plug gasket in routine oil-change planning helps keep the sealing point in view during a service. Once the plug has been removed, inspect the washer and the surrounding contact surfaces rather than assuming that the old component is suitable for reuse. A fresh, correctly matched washer can help restore the intended sealing interface when the drain plug is reinstalled, while careful checking helps identify a mismatch before the vehicle is returned to service.
For professional service operations, keeping the washer reference with the vehicle’s maintenance record can make future parts identification more straightforward. For individual maintenance, checking the OE number before starting helps avoid interruptions caused by an incorrect part. In either case, matching the component to the application supports orderly work, reduces uncertainty during reassembly, and helps the technician or owner focus on the condition of the plug, washer, and mating surface together.
This listing identifies the item as an oil drain plug gasket, crush washer, seal, or ring and provides the listed vehicle makes and OE comparisons for reference. No additional dimensions, material, or installation torque are specified here. Use the applicable vehicle service instructions for installation details, and verify the part number and fitment before use. Careful part matching and sound service practice are the practical steps that help make this small replacement component useful in ongoing vehicle maintenance.
Send an Inquiry
Related Products
Yjm Oil Sump Gasket 11 13 7 600 482
Fitment The YJM oil sump gasket, reference 11 13 7 600 482, is listed for both left-hand-drive and right-hand-drive models. This fitment information is intended···
Yjm Oil Sump Gasket 11 13 7 511 224
Fitment This YJM oil sump gasket is listed for the BMW vehicle applications below. Use the fitment information as a starting point when identifying a replacemen···
Seal Oil Filter Housing Engine Side Bmw Petrol 11427537293
This product is identified as a seal for the engine-side oil filter housing on BMW petrol vehicles. The product reference is 11427537293. When servicing the oil···
Oil Sump Gasket 11137548031 Bmw
BMW Oil Sump Gasket 11137548031 The oil sump gasket identified by part number 11137548031 is a BMW replacement part intended for use at the joint between the en···