Transfer Case Input Shaft Oil Seal Toyota 9031143008
Product details Condition (used, new): new Type: radial oil seal External diameter (mm): 58 mm Internal diameter: 43 mm Height (mm): 8 mm Product overview Transfer case input shaft oil seal for
Send Inquiry
Product details
Product overview
Transfer case input shaft oil seal for Toyota Prado, Hilux, Lexus GX460, LC120 and LC150 applications. 9031143008
Transfer case input shaft seal application
This new radial oil seal is identified as a transfer case input shaft oil seal, part number 9031143008. It is listed for Toyota Prado, Toyota Hilux, Lexus GX460, LC120 and LC150 applications. The part reference and vehicle names provide a starting point when identifying a replacement for a service or repair job. Because vehicle fitment can depend on the specific application, compare the part number and the vehicle’s existing component details before ordering or installation.
An input shaft seal is used at the transfer case shaft opening, where sealing around the shaft is required. As a radial oil seal, this component is intended for a shaft-and-housing arrangement rather than as a general-purpose flat gasket. Its application is relevant when inspecting or servicing the transfer case area and a seal replacement is needed. Selecting the correct seal helps keep the repair aligned with the original component’s specified location and purpose.
The product listing identifies the seal as new and provides its key measurements for comparison: 58 mm external diameter, 43 mm internal diameter and 8 mm height. These values can assist with checking the part against the removed seal or the requirements for the intended application. Confirm measurements and part identification carefully before fitting; the stated details should be used as supplied and do not replace vehicle-specific service information.
Dimensions and identification
The seal’s stated dimensions are an external diameter of 58 mm, an internal diameter of 43 mm and a height of 8 mm. The external measurement describes the outside size for the housing side, while the internal measurement corresponds to the shaft opening. Height is also included as a fitment reference. Together, these specifications support a practical side-by-side comparison during parts selection, especially when an existing seal is available for inspection.
- Product: transfer case input shaft oil seal.
- Part number: 9031143008.
- Condition: new.
- Type: radial oil seal.
- External diameter: 58 mm; internal diameter: 43 mm; height: 8 mm.
Keeping the part number and all three measurements together helps reduce confusion between visually similar sealing components. If purchasing for stock, workshop use or an individual repair, record the full reference rather than relying on a broad description alone. The model names listed in the overview can help narrow the application, while confirmation against the vehicle and relevant parts information remains important for choosing the correct item.
Service and maintenance value
A correctly identified transfer case input shaft seal is a focused replacement part for maintenance work involving the transfer case input area. During inspection, technicians can use the 9031143008 reference and listed dimensions to assess whether this is the component required for the repair. Replacing a seal when appropriate can form part of restoring the sealing function at the shaft opening; the condition of surrounding components and the reason for service should also be assessed as part of the repair process.
Careful preparation supports a suitable installation. Compare the replacement with the removed component, verify the sealing location and follow the vehicle’s applicable service procedure. Keep mating surfaces clean and handle the seal appropriately during fitting to avoid damage. This listing does not specify installation tools, torque values, service intervals or additional operating parameters, so those details should be taken from the relevant vehicle repair information rather than assumed from the product description.
For parts buyers and repair professionals, clear identification is useful when planning work, sourcing a replacement or organizing workshop inventory. The new condition, radial oil seal type, Toyota part reference and stated vehicle applications provide concise points for a fitment check. Accurate matching helps ensure that the selected component corresponds to the intended transfer case input shaft position before work proceeds.
Application confirmation
This listing covers the transfer case input shaft oil seal Toyota 9031143008 and names Toyota Prado, Hilux, Lexus GX460, LC120 and LC150 in the product overview. Use the full part number when checking compatibility, and verify the specific vehicle application before purchase because a model name by itself may not confirm the required component. The dimensions provided here are 58 mm external diameter, 43 mm internal diameter and 8 mm height.
Whether sourcing for scheduled maintenance, a diagnosed repair or parts inventory, compare the part reference and measurements with reliable vehicle-specific information. This description states the product’s supplied identification and measurements without adding unsupported fitment years, material details or installation specifications. Confirming those details for the intended vehicle helps make the purchase and subsequent service process more accurate.
Send an Inquiry
Related Products
Yjm Oil Sump Gasket 11 13 7 600 482
Fitment The YJM oil sump gasket, reference 11 13 7 600 482, is listed for both left-hand-drive and right-hand-drive models. This fitment information is intended···
Yjm Oil Sump Gasket 11 13 7 511 224
Fitment This YJM oil sump gasket is listed for the BMW vehicle applications below. Use the fitment information as a starting point when identifying a replacemen···
Seal Oil Filter Housing Engine Side Bmw Petrol 11427537293
This product is identified as a seal for the engine-side oil filter housing on BMW petrol vehicles. The product reference is 11427537293. When servicing the oil···
Oil Sump Gasket 11137548031 Bmw
BMW Oil Sump Gasket 11137548031 The oil sump gasket identified by part number 11137548031 is a BMW replacement part intended for use at the joint between the en···