Toyota Transfer Case Output Shaft Seal Front 9031136006
Features The Toyota transfer case output shaft seal, front position, is identified by part number 9031136006. This replacement part is intended for the front output-shaft seal location in a transfer
Send InquiryToyota Transfer Case Output Shaft Seal Front 9031136006
Features
The Toyota transfer case output shaft seal, front position, is identified by part number 9031136006. This replacement part is intended for the front output-shaft seal location in a transfer case application. Its purpose is to provide a sealing point around the shaft where it passes through the case, helping the assembly retain its lubricating fluid and limit unwanted leakage at that opening. The product is listed as new, and the details below identify its condition, type, position, and part number.
Condition New: A brand-new, unused, unopened, undamaged item in its original packaging
Part Type: Transfer Case Output Shaft Seal
Part Number: 9031136006
Position Name: Front
Function and practical value
A transfer case output shaft seal serves an important containment role in the drivetrain. At the front output location, the seal helps control the interface between the rotating shaft and the stationary case. A properly functioning seal supports fluid retention at this point while allowing the shaft to operate as part of the transfer case assembly. It is a focused service component, rather than a replacement for the transfer case or output shaft itself.
When servicing a transfer case, replacing a worn or damaged seal can help address leakage at the shaft opening and support continued lubrication of the assembly. This can be useful during a repair prompted by visible fluid seepage, during related drivetrain maintenance, or when access to the seal is already available as part of a broader service. The seal’s value is practical: it helps maintain the intended barrier at the front output position and supports routine care of the transfer case.
Leakage can have more than one possible cause, so the seal should be evaluated in the context of the surrounding components and the observed condition. Confirming the source before replacement helps ensure that the repair addresses the relevant location. After service, checking the area for signs of renewed leakage can help verify that the work is holding and make it easier to identify any additional issue that may need attention.
Application and installation considerations
The part number and position are key details when selecting this seal. Part number 9031136006 identifies the product, while “Front” specifies its named position. Before ordering or installation, compare these details with the vehicle’s service information and the part being removed. Vehicle fitment can depend on the specific application, so confirm the correct part using the vehicle identification details or an authoritative parts reference rather than relying on the product name alone.
Seal replacement involves working at the transfer case output-shaft area. The exact access and service procedure can vary by vehicle and assembly. Follow the applicable repair information for disassembly, installation, and fluid handling. During the repair, a technician can assess the shaft and the seal’s contact area for wear, damage, contamination, or other conditions that could affect sealing. Careful handling and correct seating are important general considerations for this type of service component.
Once the seal is installed, complete any required reassembly and fluid checks according to the relevant service procedure. Keeping the work area clean and inspecting for leaks after service are sensible maintenance steps. If there are signs of continuing leakage, further diagnosis may be needed; replacing a seal alone may not resolve issues caused by another damaged or worn component. Qualified installation is recommended when the repair procedure or application is uncertain.
Product details and selection summary
This listing describes one transfer case output shaft seal for the front position, with part number 9031136006. The condition is stated as new: brand-new, unused, unopened, and undamaged in its original packaging. These details make it easier to distinguish the listed component from other seal positions and from different transfer case service parts when preparing a repair or checking an order.
Use the stated part number and front-position designation as the primary product identifiers when discussing the part with a parts professional or comparing it with service documentation. Review the packaging and product identification when the item arrives, and make sure the intended application is confirmed before beginning work. These simple checks can help avoid delays, reduce the risk of selecting a seal for a different location, and keep maintenance planning focused on the correct component.
For workshops, parts departments, and vehicle owners arranging a transfer case repair, this listing provides the essential identification needed to evaluate the seal for a front output-shaft service. It does not state additional dimensions, materials, or vehicle-specific fitment details; consult the appropriate catalog or repair information for those application requirements. Selecting by verified part number and position helps support accurate parts ordering and a more organized maintenance process.
Send an Inquiry
Related Products
Yjm Oil Sump Gasket 11 13 7 600 482
Fitment The YJM oil sump gasket, reference 11 13 7 600 482, is listed for both left-hand-drive and right-hand-drive models. This fitment information is intended···
Yjm Oil Sump Gasket 11 13 7 511 224
Fitment This YJM oil sump gasket is listed for the BMW vehicle applications below. Use the fitment information as a starting point when identifying a replacemen···
Seal Oil Filter Housing Engine Side Bmw Petrol 11427537293
This product is identified as a seal for the engine-side oil filter housing on BMW petrol vehicles. The product reference is 11427537293. When servicing the oil···
Oil Sump Gasket 11137548031 Bmw
BMW Oil Sump Gasket 11137548031 The oil sump gasket identified by part number 11137548031 is a BMW replacement part intended for use at the joint between the en···